WHAT YOU WILL LEARN?
Hardware: DSBOARD-ORNXS v1.11
Forecr’s DSBOARD-ORNXS v1.11 is industrial carrier board based on Nvidia Jetson Orin NX & Orin Nano processor modules for edge analytics. It is compatible with multi stream deep learning applications.
DSBOARD-ORNXS Recovery Pushbutton
The DSBOARD-ORNXS implements a recovery pushbutton. Recovery button should be pressed with reset button at the same time. After released reset button, recovery button should be pressed a little bit more (min. 250 ms). It is located on the top side of the board.
DSBOARD-ORNXS Reset Pushbutton
The DSBOARD-ORNXS implements a reset button. It is recommended to use needle-like material. It is located on the top side of the board.
DSBOARD-ORNXS Bluetooth Switch
The DSBOARD-ORNXS implements a slide switch for using USB interface on the M.2 Key-E slot or USBHS2 connector. If the switch is in OFF state, the USB is available on the Key-E slot (The same info located on the silkscreen next to it). This connector is located on the top side of the board.
DSBOARD-ORNXS Power Connector
The DSBOARD-ORNXS implements 2-Pin Power Terminal Connector that accepts +9V to +28 DC power. The mating connector is "0436450200" produced by Molex. The first pin is negative, second one is positive. The power connector is located on the rear side of the board.
DSBOARD-ORNXS M.2 Key-M Connector
The DSBOARD-ORNXS implements one M.2 M-Key Connector (2230) for suitable modules.
DSBOARD-ORNXS M.2 Key-E Connector
The DSBOARD-ORNXS implements a M.2 E-Key Connector for suitable modules. This connector is located on the top side of the board.
DSBOARD-ORNXS CSI Connectors
The DSBOARD-ORNXS implements 2 CSI 4-lane camera connectors. The connector model is "687322124422" produced by Wurth Elektronik. It is located on the bottom side of the board.
DSBOARD-ORNXS I/O Terminal Connector
The DSBOARD-ORNXS implements 28-pin I/O terminal connector which has 2x UART, 2x I2C, 1x I2S and 1x SPI standard pins. The mating connector is "5054322801" produced by Molex. It is located on the bottom side of the board.
DSBOARD-ORNXS Panel Connector
The recovery, reset & power button's signals located at the panel connector. The mating connector is "0510210600" produced by Molex.
DSBOARD-ORNXS RTC Battery Connector
The DSBOARD-ORNXS implements a RTC battery connector. The mating connector is "5055650201" produced by Molex. The first pin is positive and the second one is negative. It is located on the rear side of the board.
DSBOARD-ORNXS Mini DisplayPort Connector
The NVIDIA® Jetson Orin modules will output video via the DSBOARD-ORNXS mini DisplayPort connector. It is located on the rear side of the board.
DSBOARD-ORNXS USB 2.0 Connectors
The DSBOARD-ORNXS incorporates 2 USB connectors. The mating connector is "5055650401" produced by Molex. The USB connector is located on the rear side of the board. One of the USB connectors (USBHS2) can be activated by the Bluetooth switch.
DSBOARD-ORNXS Gigabit Ethernet Connectors
The DSBOARD-ORNXS implements 2 Gigabit Ethernet connectors for internet communication. The mating connector is "5055650801" produced by Molex.
DSBOARD-ORNXS Fan Connector
The DSBOARD-ORNXS implements a fan connector. The mating connector is "0510210400" produced by Molex. It is located on the bottom side of the board.
DSBOARD-ORNXS CAN Bus Connector
The DSBOARD-ORNXS implements a connector to access its CAN Bus interface. The mating connector is "5055650301" produced by Molex. It is located on the rear side of the board.
DSBOARD-ORNXS Recovery Mode USB Type-C Connector
The DSBOARD-ORNXS implements a USB Type-C connector to allow to install or upgrade the operating system. It is located on the rear side of the board.
DSBOARD-ORNXS Debug Mode Connector
The DSBOARD-ORNXS implements a connector to access the module by using serial connection. The mating connector is "5055650301" produced by Molex. It is located on the rear side of the board.
Thank you for reading our blog post.
